How To Burn A Candle Correctly

If you’re like most people, you probably grew up using candles. Whether for religious purposes, to make a wish, or just to set the mood, candles are a part of many people’s lives. But did you know that there is a right and wrong way to burn a candle?

Most people don’t realize that there is such a thing as proper candle etiquette. For example, did you know that you should never blow out a candle? The correct way to extinguish a flame is to use a snuffer.

Blowing out a candle can cause the hot wax to splatter and can be dangerous.

  • Trim the wick to about 1/4 inch before lighting
  • This will help prevent smoking and soot buildup on the glass
  • Light the candle in a well-ventilated room, away from drafts, vents or anything that could fan the flame
  • Allow the wax pool to reach the edge of the container before blowing out the flame
  • This allows for an even burn and prevents “tunneling
  • If you must blow out your candle before it has reached a full melt pool, re-center and realign the wick as best as possible before relighting

How to burn a candle the RIGHT WAY

How Do I Know If My Candle is Burning Correctly?

When it comes to candles, there are a few tell-tale signs that can indicate whether or not your candle is burning correctly. Here are a few things to look for: 1. The Flame – The flame should be tall and slender, with a bright blue tip.

If the flame is flickering excessively or if it is smoky, this could be an indication that the wick needs to be trimmed. 2. The Wick – The wick should be evenly burned across its length. If you see any black soot around the wick, this means that the flame is not burning correctly and the wick needs to be trimmed.

3. The Wax Pool – The wax pool should be even and free of any tunneling (hollow areas in the wax). If the wax pool is uneven or has tunnels, this indicates that the candle is not burning evenly and will likely cause problems down the road such as premature extinguished flames or soot buildup on glass surfaces.

How Do You Stop Candles from Tunneling?

Candles tunneling occurs when the flame of the candle burns down the middle of the wax, leaving a hole or tunnel. This usually happens when a candle is not burned properly or if it is made with poor quality wax. There are a few things you can do to prevent your candles from tunneling.

When burning a candle, make sure to keep an eye on it and trim the wick as needed so that it doesn’t get too long. If the wick gets too long, it will cause the flame to burn down the middle of the candle instead of evenly across the surface. You also want to make sure that you’re using a good quality wax for your candles.

Some cheaper waxes tend to tunnel more easily than higher quality ones. Finally, don’t let your candles burn all the way down to nothing – this will also cause them to tunnel. If you see that your candle is getting low, extinguish it and save it for another time.

How Long Should You Burn Candle for the First Time?

When you light a candle for the first time, you should let it burn for at least 2 hours. This allows the wax to melt evenly and creates a “memory” for the candle. If you extinguish a candle before it has fully burned, it will “remember” that partial burn and may not light as evenly next time.

Do You Light All 3 Wicks?

If you’re using a 3 wick candle, do you have to light all 3 wicks? The answer is no, but there are a few things to keep in mind. First, when you light a 3 wick candle, the middle wick will usually burn the fastest.

So if you’re looking for an even burn, it’s best to start by lighting the outer two wicks first. This will help the middle wick last longer. Second, if you only light one or two of the wicks, the flame may be too small to properly melt the wax around all three wicks.

This can cause your candle to tunnel (burn down the center without melting the wax around the edges). So if you want to get the most out of your 3 wick candle, light all three wicks!

How To Burn A Candle Correctly


How to Burn a Candle for the First Time

If you’re like most people, you’ve probably never given much thought to how to burn a candle. After all, it’s just a piece of wax with a wick, right? Wrong!

If you want to get the most out of your candles and avoid any potential hazards, there are a few things you need to know about how to burn a candle for the first time. Here are the basics: 1. Trim the wick.

Before you light your candle, use a wick trimmer or scissors to trim the wick down to about 1/4 inch. This will help prevent the flame from getting too big and reduce soot buildup on the glass jar or holder. 2. Place your candle on a heat-resistant surface.

Make sure that whatever surface you place your candle on can withstand the heat of the flame without melting or catching fire. A good rule of thumb is to put it on something that would also be safe for hot coffee cups or plates. 3..

Use a lighter or matches, never candles themselves, to light your wicks . Hold the flame close to (but not touching) the wick until it’s lit evenly across its entire length . You may need to do this several times before lighting takes hold – be patient!

Once it’s lit , let it burn for at least 30 minutes so that the wax melts evenly across the surface . This will help prevent “tunneling” – when only part of the wax burns , leaving an unmelted core in middle .


The first step is to find a safe, flat surface away from anything that can catch fire. Make sure the wick is trimmed to about 1/4 inch before lighting the candle. This will help prevent the flame from getting too big and reduce soot buildup.

To light the candle, use a long match or lighter so you don’t burn your fingers. Hold the flame to the wick for a few seconds until it lights. Once lit, allow the candle to burn for at least 30 minutes so that the wax can melt evenly across the surface of the candle.

If you blow out a candle before it has been burning for at least 30 minutes, there will be an uneven “pool” of wax around the wick which can cause your candles to smoke when relit.

Leave a Reply

Your email address will not be published. Required fields are marked *